M10 threaded studs with ergonomic plastic handle for seat track and air cargo pallet connection. Clamping range from 0 to 52 mm across the range. 2 000 daN vertical / 500 daN lateral.
Data sheet
The threaded studs with ergonomic plastic handle connect equipment, seats and accessory rails to the seat track or to an air cargo pallet attachment, with the ergonomic handle allowing tool-free clamping by hand. They are used in cabin reconfigurations, role changes and quick-installation kits where time on the floor matters.
All references use an M10 thread and provide 2 000 daN vertical (Z) and 500 daN lateral (X/Y) restraint capacity. Five clamping ranges cover the standard installations: 0-5 mm, 7-12 mm, 13-22 mm, 23-32 mm and 44-52 mm.
Construction is zinc-plated steel with a plastic handle.
16 other products in the same category:
Single stud fittings with rings give a one-position anchor point on a seat track or air cargo pallet rail, with an integrated ring that takes the strap or hook directly. They are used for...
The lifting ring is a stainless steel delta ring fitted with 4 flat hooks, used as the central gathering point of a lifting net assembly. Each hook is sewn to one corner of the lifting net, and the...
D-rings are half-round anchor parts used as fixed attachment points for restraint strap and net assemblies. The flat side takes the webbing loop and the round side receives the hook, snap or...
Flat snap hooks are end fittings for restraint strap assemblies, used to connect the webbing to cabin anchor rings, footman loops and floor fittings. A hinged latch is mounted on a rivet and closes...
This end fitting carries a latched hook mounted on a triangular delta ring, the delta ring taking the 50 mm webbing and the latched hook engaging on anchor rings, floor fittings and other...
The hook with keeper is a two-part strap end fitting used for a secured attachment to an anchor ring or bar. Both the male part (a double J hook with keeper wire on a delta ring) and the female...
Flat hooks are end fittings for restraint strap assemblies, connecting the webbing to cabin anchor rings, footman loops and floor fittings. The open-throat shape gives fast hook-on and hook-off in...
The threaded studs with nut connect equipment, seats and accessory rails to the seat track or to an air cargo pallet attachment, with a standard hex nut that is torqued with a wrench. They are the...
Footman loops are U-shaped bolt-down anchor points fixed to the cabin floor, cargo platform or equipment panel, giving a hook-on point for a restraint or lashing strap. They are the most common...
Rectangular rings are designed to connect two different webbing for an assembly. The range covers four rectangular sizes from 16 to 23 mm with ultimate loads from 100 to 300 daN, and one small...
Double J hooks are end fittings formed of two J-shaped wire fingers joined to a triangular webbing loop. The two fingers hook onto bars, floor fittings and anchor points, giving a stable engagement...
Belt buckles supply a quick connection for light belt and restraint assemblies, with male and female parts forming the complete buckle. They are used for equipment belts, light cabin restraints and...
Quick links are reusable connectors with a screw-gate closure: a threaded sleeve runs along the gate to lock the link closed once a strap or ring is engaged. They replace permanent shackles where a...
Double stud fittings engage two adjacent positions of a seat track or air cargo pallet rail, giving a stronger anchor point than a single stud. They are the standard anchor format for ULD restraint...
This PVC tarpaulin is the fire-resistant grade specified for use in aircraft cabins and air cargo holds, where any covering material must meet flammability requirements. It is used for load...
This hook-and-loop fastener system is the aerospace counterpart of standard Velcro tape, used in cabin assemblies where a removable fixture is required and where a fire-retardant textile is...
M10 threaded studs with ergonomic plastic handle for seat track and air cargo pallet connection. Clamping range from 0 to 52 mm across the range. 2 000 daN vertical / 500 daN lateral.
