Hook with keeper for 50 mm webbing, 3 300 daN ultimate load, zinc-plated steel. Two-part end fitting (male hook + female delta ring) that locks around an anchor ring as soon as the strap is tensioned.
Data sheet
The hook with keeper is a two-part strap end fitting used for a secured attachment to an anchor ring or bar. Both the male part (a double J hook with keeper wire on a delta ring) and the female part (a plain delta ring) are mounted on the same webbing loop at the strap end.
In use, the male hook engages on the anchor ring, the female delta ring closes back over the hook, and webbing tension keeps the two parts together around the ring. As long as the strap stays under load, the connection cannot accidentally release; deliberate slack must be introduced to take the fitting off the ring. The result is a fast, tool-free attachment that stays secured throughout normal handling and vibration.
Ultimate load is 3 300 daN per part for 50 mm webbing. Construction is zinc-plated steel for corrosion resistance, with the female part at 82.7 g and the male part at 151.5 g.
Stocked as spare parts. Each strap end uses one male and one female part on the same webbing loop.
16 other products in the same category:
The seat track covering is a flexible strip that fits into unused seat track sections to keep debris, fluids and foreign objects out of the rail pitch. It protects the track and reduces foreign...
The ASNA flat polyester webbing range is manufactured in conformity with Airbus ASNA 3573 standards and is approved for use in aircraft applications under FAR 25 appendix F. It is used for...
Quick links are reusable connectors with a screw-gate closure: a threaded sleeve runs along the gate to lock the link closed once a strap or ring is engaged. They replace permanent shackles where a...
Flat snap hooks are end fittings for restraint strap assemblies, used to connect the webbing to cabin anchor rings, footman loops and floor fittings. A hinged latch is mounted on a rivet and closes...
This end fitting carries a latched hook mounted on a triangular delta ring, the delta ring taking the 50 mm webbing and the latched hook engaging on anchor rings, floor fittings and other...
Double stud fittings engage two adjacent positions of a seat track or air cargo pallet rail, giving a stronger anchor point than a single stud. They are the standard anchor format for ULD restraint...
Rectangular rings are designed to connect two different webbing for an assembly. The range covers four rectangular sizes from 16 to 23 mm with ultimate loads from 100 to 300 daN, and one small...
Slide buckles are length-adjustment fittings for webbing straps. The webbing threads through the buckle and locks by friction, allowing manual adjustment of the strap length without a tensioning...
This tubular polyester webbing is used for corner ropes and lashing assemblies in air transport. The tubular construction spreads the load around the full circumference of the strap, which limits...
This single stud fitting integrates a length adjuster on the stud body, so one component handles both the seat track or pallet anchor and the adjustment of the connected strap. It simplifies...
S hooks are open end fittings shaped to connect a restraint strap to a bar, anchor ring or rail. The open S-shape allows fast attachment, while latch versions add a safety catch that keeps the hook...
Round rings are closed anchor parts used as connection points in restraint, tie-down and lifting assemblies. The closed shape lets straps, slings and connectors run all the way around the ring,...
Snap latches are spring-loaded closures used in cabin restraint and equipment assemblies, where a strap needs to be opened and re-closed often and without tools. A press on the latch releases the...
The threaded studs with ergonomic plastic handle connect equipment, seats and accessory rails to the seat track or to an air cargo pallet attachment, with the ergonomic handle allowing tool-free...
This aircraft seatbelt buckle is used in cabin seat belt and occupant restraint assemblies. It supplies the quick-release connection between the two webbing ends, with male and female parts forming...
Flat hooks are end fittings for restraint strap assemblies, connecting the webbing to cabin anchor rings, footman loops and floor fittings. The open-throat shape gives fast hook-on and hook-off in...
Viewed products
The bi-pass buckle is a flat two-slot steel plate for 50 mm webbing. The webbing passes through one slot and back through the second, where it locks by friction. Depending on how it is threaded,...
Hook with keeper for 50 mm webbing, 3 300 daN ultimate load, zinc-plated steel. Two-part end fitting (male hook + female delta ring) that locks around an anchor ring as soon as the strap is tensioned.
