Flat hooks for 25 and 45 mm webbing, ultimate loads from 450 to 1 500 daN. Zinc-plated steel. Open-throat end fittings for cabin anchor rings and footman loops, retainer stud versions available.
Data sheet
Flat hooks are end fittings for restraint strap assemblies, connecting the webbing to cabin anchor rings, footman loops and floor fittings. The open-throat shape gives fast hook-on and hook-off in cabin and cargo operations, where speed of attachment matters.
Two retainer-stud versions are available at 25 mm to lock the webbing in place once the hook is engaged: a spring-loaded stud at 1 500 daN and a standard stud at 1 000 daN. The range also covers a 25 mm light version at 450 daN and a 45 mm version at 1 500 daN.
Construction is zinc-plated steel for corrosion resistance, with unit weights from 24.5 to 166 g. Stocked as spare parts, compatible with the corresponding GPI Forankra webbing widths.
16 other products in the same category:
The hook with keeper is a two-part strap end fitting used for a secured attachment to an anchor ring or bar. Both the male part (a double J hook with keeper wire on a delta ring) and the female...
Fixation plates are flat anchor parts used to bolt the end of a webbing strap to the airframe, a load platform or any structure with matching threaded holes. The webbing loops through the plate,...
Flat snap hooks are end fittings for restraint strap assemblies, used to connect the webbing to cabin anchor rings, footman loops and floor fittings. A hinged latch is mounted on a rivet and closes...
Slide buckles are length-adjustment fittings for webbing straps. The webbing threads through the buckle and locks by friction, allowing manual adjustment of the strap length without a tensioning...
The threaded studs with nut connect equipment, seats and accessory rails to the seat track or to an air cargo pallet attachment, with a standard hex nut that is torqued with a wrench. They are the...
S hooks are open end fittings shaped to connect a restraint strap to a bar, anchor ring or rail. The open S-shape allows fast attachment, while latch versions add a safety catch that keeps the hook...
The seat track covering is a flexible strip that fits into unused seat track sections to keep debris, fluids and foreign objects out of the rail pitch. It protects the track and reduces foreign...
Round rings are closed anchor parts used as connection points in restraint, tie-down and lifting assemblies. The closed shape lets straps, slings and connectors run all the way around the ring,...
This aluminium double anchor plate provides a reinforced attachment point for stud fittings in cargo restraint assemblies that call for a higher load rating than the standard anchor plate. It...
This end fitting carries a latched hook mounted on a triangular delta ring, the delta ring taking the 50 mm webbing and the latched hook engaging on anchor rings, floor fittings and other...
Over-center buckles are manual tensioning devices that lock the strap with a single lever movement. Compared with a ratchet, the over-center action gives fast, repeatable tension setting without...
This plastic hook is a lightweight end fitting for 13 mm rope, used in light securing and accessory applications where metal hardware is not required. The plastic construction avoids marking and...
The ASNA flat polyester webbing range is manufactured in conformity with Airbus ASNA 3573 standards and is approved for use in aircraft applications under FAR 25 appendix F. It is used for...
Rectangular rings are designed to connect two different webbing for an assembly. The range covers four rectangular sizes from 16 to 23 mm with ultimate loads from 100 to 300 daN, and one small...
This range of 25 mm flat polyester webbing is used for restraint and lashing assemblies in air transport, where strength, regulatory compliance and color identification matter. It is approved for...
Double J hooks are end fittings formed of two J-shaped wire fingers joined to a triangular webbing loop. The two fingers hook onto bars, floor fittings and anchor points, giving a stable engagement...
Viewed products
Double J hooks are end fittings formed of two J-shaped wire fingers joined to a triangular webbing loop. The two fingers hook onto bars, floor fittings and anchor points, giving a stable engagement...
Flat hooks for 25 and 45 mm webbing, ultimate loads from 450 to 1 500 daN. Zinc-plated steel. Open-throat end fittings for cabin anchor rings and footman loops, retainer stud versions available.
