M10 threaded studs with nut for seat track and air cargo pallet connection. Clamping range from 0 to 52 mm. 2 000 daN vertical / 500 daN lateral. Tool-tightened version.
Data sheet
The threaded studs with nut connect equipment, seats and accessory rails to the seat track or to an air cargo pallet attachment, with a standard hex nut that is torqued with a wrench. They are the tool-tightened counterpart of the ergonomic-handle version, used in permanent or semi-permanent installations where calibrated torque is required.
All references use an M10 thread and provide 2 000 daN vertical (Z) and 500 daN lateral (X/Y) restraint capacity. Four clamping ranges cover the standard installations: 0-12 mm, 0-22 mm, 0-32 mm and 0-52 mm.
Construction is zinc-plated steel.
16 other products in the same category:
Footman loops are U-shaped bolt-down anchor points fixed to the cabin floor, cargo platform or equipment panel, giving a hook-on point for a restraint or lashing strap. They are the most common...
The threaded studs with ergonomic plastic handle connect equipment, seats and accessory rails to the seat track or to an air cargo pallet attachment, with the ergonomic handle allowing tool-free...
The hook with keeper is a two-part strap end fitting used for a secured attachment to an anchor ring or bar. Both the male part (a double J hook with keeper wire on a delta ring) and the female...
Quick links are reusable connectors with a screw-gate closure: a threaded sleeve runs along the gate to lock the link closed once a strap or ring is engaged. They replace permanent shackles where a...
The 50 mm twisted snap hook is a heavy-duty end fitting for restraint strap assemblies. The hook body is rotated 90° relative to the webbing slot, so the strap lies flat against the airframe or...
The lifting ring is a stainless steel delta ring fitted with 4 flat hooks, used as the central gathering point of a lifting net assembly. Each hook is sewn to one corner of the lifting net, and the...
S hooks are open end fittings shaped to connect a restraint strap to a bar, anchor ring or rail. The open S-shape allows fast attachment, while latch versions add a safety catch that keeps the hook...
This single stud fitting integrates a length adjuster on the stud body, so one component handles both the seat track or pallet anchor and the adjustment of the connected strap. It simplifies...
Single stud fittings with rings give a one-position anchor point on a seat track or air cargo pallet rail, with an integrated ring that takes the strap or hook directly. They are used for...
This plastic hook is a lightweight end fitting for 13 mm rope, used in light securing and accessory applications where metal hardware is not required. The plastic construction avoids marking and...
This tubular polyester webbing is used for corner ropes and lashing assemblies in air transport. The tubular construction spreads the load around the full circumference of the strap, which limits...
This aircraft seatbelt buckle is used in cabin seat belt and occupant restraint assemblies. It supplies the quick-release connection between the two webbing ends, with male and female parts forming...
Over-center buckles are manual tensioning devices that lock the strap with a single lever movement. Compared with a ratchet, the over-center action gives fast, repeatable tension setting without...
Fixation plates are flat anchor parts used to bolt the end of a webbing strap to the airframe, a load platform or any structure with matching threaded holes. The webbing loops through the plate,...
The seat track range provides aluminium anchoring rails for aircraft seats, cargo restraint systems and cabin equipment. Seat tracks accept stud and stud-fitting hardware along a standardized...
Rectangular rings are designed to connect two different webbing for an assembly. The range covers four rectangular sizes from 16 to 23 mm with ultimate loads from 100 to 300 daN, and one small...
Viewed products
This end fitting carries a latched hook mounted on a triangular delta ring, the delta ring taking the 50 mm webbing and the latched hook engaging on anchor rings, floor fittings and other...
M10 threaded studs with nut for seat track and air cargo pallet connection. Clamping range from 0 to 52 mm. 2 000 daN vertical / 500 daN lateral. Tool-tightened version.
