Adjusting plates for 25 and 50 mm webbing, 2 500 daN ultimate load, zinc-plated steel. Length adjustment hardware for restraint and lashing assemblies.
Data sheet
Adjusting plates are flat steel parts with internal slots that let the webbing fold back on itself and lock by friction, setting the strap length without a buckle. They are used where the assembly does not need a tensioning mechanism, just a fixed length adjustment.
Two sizes cover the range: 25 mm at 35.8 x 30.3 mm (3 mm thick, 18 g) and 50 mm at 74.6 x 45.6 mm (4 mm thick, 79.6 g). Ultimate load is 2 500 daN for both sizes. Construction is zinc-plated steel for corrosion resistance.
Stocked as spare parts, compatible with the corresponding GPI Forankra webbing widths.
16 other products in the same category:
This hook combines a fixed eye for permanent attachment with a hooking end fitted with a safety latch. The eye is sewn or pinned to the net edge, and the latched hook engages cabin anchor rings,...
The cargo hook is mounted on the cargo net itself and engages directly in the net mesh to set the working height of the net and adjust its tension over the load. Repositioning the hook from one...
This range of 25 mm flat polyester webbing is used for restraint and lashing assemblies in air transport, where strength, regulatory compliance and color identification matter. It is approved for...
The threaded studs with nut connect equipment, seats and accessory rails to the seat track or to an air cargo pallet attachment, with a standard hex nut that is torqued with a wrench. They are the...
The threaded studs with ergonomic plastic handle connect equipment, seats and accessory rails to the seat track or to an air cargo pallet attachment, with the ergonomic handle allowing tool-free...
D-rings are half-round anchor parts used as fixed attachment points for restraint strap and net assemblies. The flat side takes the webbing loop and the round side receives the hook, snap or...
The hook with keeper is a two-part strap end fitting used for a secured attachment to an anchor ring or bar. Both the male part (a double J hook with keeper wire on a delta ring) and the female...
This aircraft seatbelt buckle is used in cabin seat belt and occupant restraint assemblies. It supplies the quick-release connection between the two webbing ends, with male and female parts forming...
Double stud fittings engage two adjacent positions of a seat track or air cargo pallet rail, giving a stronger anchor point than a single stud. They are the standard anchor format for ULD restraint...
Ratchet buckles are manual tensioning devices for restraint and lashing straps. The ratchet mechanism applies and holds high tension in controlled increments, which makes it the standard choice for...
The seat track covering is a flexible strip that fits into unused seat track sections to keep debris, fluids and foreign objects out of the rail pitch. It protects the track and reduces foreign...
This hook-and-loop fastener system is the aerospace counterpart of standard Velcro tape, used in cabin assemblies where a removable fixture is required and where a fire-retardant textile is...
Rectangular rings are designed to connect two different webbing for an assembly. The range covers four rectangular sizes from 16 to 23 mm with ultimate loads from 100 to 300 daN, and one small...
The ASNA flat polyester webbing range is manufactured in conformity with Airbus ASNA 3573 standards and is approved for use in aircraft applications under FAR 25 appendix F. It is used for...
Round rings are closed anchor parts used as connection points in restraint, tie-down and lifting assemblies. The closed shape lets straps, slings and connectors run all the way around the ring,...
Belt buckles supply a quick connection for light belt and restraint assemblies, with male and female parts forming the complete buckle. They are used for equipment belts, light cabin restraints and...
Viewed products
The threaded studs with nut connect equipment, seats and accessory rails to the seat track or to an air cargo pallet attachment, with a standard hex nut that is torqued with a wrench. They are the...
Adjusting plates for 25 and 50 mm webbing, 2 500 daN ultimate load, zinc-plated steel. Length adjustment hardware for restraint and lashing assemblies.
