Hook with keeper for 50 mm webbing, 3 300 daN ultimate load, zinc-plated steel. Two-part end fitting (male hook + female delta ring) that locks around an anchor ring as soon as the strap is tensioned.
Data sheet
The hook with keeper is a two-part strap end fitting used for a secured attachment to an anchor ring or bar. Both the male part (a double J hook with keeper wire on a delta ring) and the female part (a plain delta ring) are mounted on the same webbing loop at the strap end.
In use, the male hook engages on the anchor ring, the female delta ring closes back over the hook, and webbing tension keeps the two parts together around the ring. As long as the strap stays under load, the connection cannot accidentally release; deliberate slack must be introduced to take the fitting off the ring. The result is a fast, tool-free attachment that stays secured throughout normal handling and vibration.
Ultimate load is 3 300 daN per part for 50 mm webbing. Construction is zinc-plated steel for corrosion resistance, with the female part at 82.7 g and the male part at 151.5 g.
Stocked as spare parts. Each strap end uses one male and one female part on the same webbing loop.
16 other products in the same category:
Quick links are reusable connectors with a screw-gate closure: a threaded sleeve runs along the gate to lock the link closed once a strap or ring is engaged. They replace permanent shackles where a...
The hook with spaced fingers is a heavy-duty end fitting whose two parallel fingers are set apart in a U-shape, engaging spaced bars, grids and double anchor points that a single-finger hook cannot...
The bi-pass buckle is a flat two-slot steel plate for 50 mm webbing. The webbing passes through one slot and back through the second, where it locks by friction. Depending on how it is threaded,...
This tubular polyester webbing is used for corner ropes and lashing assemblies in air transport. The tubular construction spreads the load around the full circumference of the strap, which limits...
Rectangular rings are designed to connect two different webbing for an assembly. The range covers four rectangular sizes from 16 to 23 mm with ultimate loads from 100 to 300 daN, and one small...
The threaded studs with nut connect equipment, seats and accessory rails to the seat track or to an air cargo pallet attachment, with a standard hex nut that is torqued with a wrench. They are the...
This end fitting carries a latched hook mounted on a triangular delta ring, the delta ring taking the 50 mm webbing and the latched hook engaging on anchor rings, floor fittings and other...
Ratchet buckles are manual tensioning devices for restraint and lashing straps. The ratchet mechanism applies and holds high tension in controlled increments, which makes it the standard choice for...
Flat snap hooks are end fittings for restraint strap assemblies, used to connect the webbing to cabin anchor rings, footman loops and floor fittings. A hinged latch is mounted on a rivet and closes...
Raschel netting is a knitted mesh fabric supplied by the metre and used to build cabin partitions, baggage retention curtains and custom net assemblies that need a textile mesh rather than a...
This plastic hook is a lightweight end fitting for 13 mm rope, used in light securing and accessory applications where metal hardware is not required. The plastic construction avoids marking and...
S hooks are open end fittings shaped to connect a restraint strap to a bar, anchor ring or rail. The open S-shape allows fast attachment, while latch versions add a safety catch that keeps the hook...
This range of 25 mm flat polyester webbing is used for restraint and lashing assemblies in air transport, where strength, regulatory compliance and color identification matter. It is approved for...
Adjusting plates are flat steel parts with internal slots that let the webbing fold back on itself and lock by friction, setting the strap length without a buckle. They are used where the assembly...
Snap latches are spring-loaded closures used in cabin restraint and equipment assemblies, where a strap needs to be opened and re-closed often and without tools. A press on the latch releases the...
The 50 mm twisted snap hook is a heavy-duty end fitting for restraint strap assemblies. The hook body is rotated 90° relative to the webbing slot, so the strap lies flat against the airframe or...
Hook with keeper for 50 mm webbing, 3 300 daN ultimate load, zinc-plated steel. Two-part end fitting (male hook + female delta ring) that locks around an anchor ring as soon as the strap is tensioned.
