Lifting ring with 4 hooks - 10 000 daN
The lifting ring is a stainless steel delta ring fitted with 4 flat hooks, used as the central gathering point of a lifting net assembly. Each hook is sewn to one corner of the lifting net, and the...
Airbus ASNA 3573 flat polyester webbings, 20 to 25 mm, ultimate loads 700 to 1200 daN. Available in black and grey. FAR 25.853 approved. Supplied on 100 m rolls.
Data sheet
The ASNA flat polyester webbing range is manufactured in conformity with Airbus ASNA 3573 standards and is approved for use in aircraft applications under FAR 25 appendix F. It is used for restraint and lashing assemblies in aeronautical environments where traceability to an Airbus specification is required.
Three references cover the range, each tied to a specific ASNA standard: ASNA 3573-5919 (20 mm, 700 daN, black), ASNA 3573-5925 (25 mm, 1200 daN, grey) and ASNA 3573-5926 (25 mm, 1200 daN, black). Thickness runs from 1 to 1.2 mm and weight from 16 to 25 g/m.
These references are used for cabin and cargo securing assemblies.
Each reference is supplied on 100 m rolls.
16 other products in the same category:
The lifting ring is a stainless steel delta ring fitted with 4 flat hooks, used as the central gathering point of a lifting net assembly. Each hook is sewn to one corner of the lifting net, and the...
Belt buckles supply a quick connection for light belt and restraint assemblies, with male and female parts forming the complete buckle. They are used for equipment belts, light cabin restraints and...
These combined fittings pair a slide adjuster with an end hook in a single part, so one component handles both length adjustment and anchoring on a 25 mm strap. They simplify light restraint...
Snap latches are spring-loaded closures used in cabin restraint and equipment assemblies, where a strap needs to be opened and re-closed often and without tools. A press on the latch releases the...
Quick links are reusable connectors with a screw-gate closure: a threaded sleeve runs along the gate to lock the link closed once a strap or ring is engaged. They replace permanent shackles where a...
The hook with spaced fingers is a heavy-duty end fitting whose two parallel fingers are set apart in a U-shape, engaging spaced bars, grids and double anchor points that a single-finger hook cannot...
Slide buckles are length-adjustment fittings for webbing straps. The webbing threads through the buckle and locks by friction, allowing manual adjustment of the strap length without a tensioning...
This plastic hook is a lightweight end fitting for 13 mm rope, used in light securing and accessory applications where metal hardware is not required. The plastic construction avoids marking and...
The cargo hook is mounted on the cargo net itself and engages directly in the net mesh to set the working height of the net and adjust its tension over the load. Repositioning the hook from one...
The threaded studs with nut connect equipment, seats and accessory rails to the seat track or to an air cargo pallet attachment, with a standard hex nut that is torqued with a wrench. They are the...
Round rings are closed anchor parts used as connection points in restraint, tie-down and lifting assemblies. The closed shape lets straps, slings and connectors run all the way around the ring,...
This end fitting carries a latched hook mounted on a triangular delta ring, the delta ring taking the 50 mm webbing and the latched hook engaging on anchor rings, floor fittings and other...
This aluminium double anchor plate provides a reinforced attachment point for stud fittings in cargo restraint assemblies that call for a higher load rating than the standard anchor plate. It...
Rectangular rings are designed to connect two different webbing for an assembly. The range covers four rectangular sizes from 16 to 23 mm with ultimate loads from 100 to 300 daN, and one small...
The hook with keeper is a two-part strap end fitting used for a secured attachment to an anchor ring or bar. Both the male part (a double J hook with keeper wire on a delta ring) and the female...
Adjusting plates are flat steel parts with internal slots that let the webbing fold back on itself and lock by friction, setting the strap length without a buckle. They are used where the assembly...
Viewed products
Flat hooks are end fittings for restraint strap assemblies, connecting the webbing to cabin anchor rings, footman loops and floor fittings. The open-throat shape gives fast hook-on and hook-off in...