Adjusting plates for 25 and 50 mm webbing, 2 500 daN ultimate load, zinc-plated steel. Length adjustment hardware for restraint and lashing assemblies.
Data sheet
Adjusting plates are flat steel parts with internal slots that let the webbing fold back on itself and lock by friction, setting the strap length without a buckle. They are used where the assembly does not need a tensioning mechanism, just a fixed length adjustment.
Two sizes cover the range: 25 mm at 35.8 x 30.3 mm (3 mm thick, 18 g) and 50 mm at 74.6 x 45.6 mm (4 mm thick, 79.6 g). Ultimate load is 2 500 daN for both sizes. Construction is zinc-plated steel for corrosion resistance.
Stocked as spare parts, compatible with the corresponding GPI Forankra webbing widths.
16 other products in the same category:
This aluminium anchor plate provides a fixed attachment point for single stud fittings in cargo restraint assemblies. It is used to anchor straps and nets to the aircraft structure or to load...
The threaded studs with ergonomic plastic handle connect equipment, seats and accessory rails to the seat track or to an air cargo pallet attachment, with the ergonomic handle allowing tool-free...
Ratchet buckles are manual tensioning devices for restraint and lashing straps. The ratchet mechanism applies and holds high tension in controlled increments, which makes it the standard choice for...
Rectangular rings are designed to connect two different webbing for an assembly. The range covers four rectangular sizes from 16 to 23 mm with ultimate loads from 100 to 300 daN, and one small...
The ASNA flat polyester webbing range is manufactured in conformity with Airbus ASNA 3573 standards and is approved for use in aircraft applications under FAR 25 appendix F. It is used for...
The hook with keeper is a two-part strap end fitting used for a secured attachment to an anchor ring or bar. Both the male part (a double J hook with keeper wire on a delta ring) and the female...
Double J hooks are end fittings formed of two J-shaped wire fingers joined to a triangular webbing loop. The two fingers hook onto bars, floor fittings and anchor points, giving a stable engagement...
The hook with spaced fingers is a heavy-duty end fitting whose two parallel fingers are set apart in a U-shape, engaging spaced bars, grids and double anchor points that a single-finger hook cannot...
The threaded studs with nut connect equipment, seats and accessory rails to the seat track or to an air cargo pallet attachment, with a standard hex nut that is torqued with a wrench. They are the...
Over-center buckles are manual tensioning devices that lock the strap with a single lever movement. Compared with a ratchet, the over-center action gives fast, repeatable tension setting without...
Flat hooks are end fittings for restraint strap assemblies, connecting the webbing to cabin anchor rings, footman loops and floor fittings. The open-throat shape gives fast hook-on and hook-off in...
Slide buckles are length-adjustment fittings for webbing straps. The webbing threads through the buckle and locks by friction, allowing manual adjustment of the strap length without a tensioning...
Quick links are reusable connectors with a screw-gate closure: a threaded sleeve runs along the gate to lock the link closed once a strap or ring is engaged. They replace permanent shackles where a...
Belt buckles supply a quick connection for light belt and restraint assemblies, with male and female parts forming the complete buckle. They are used for equipment belts, light cabin restraints and...
This aluminium double anchor plate provides a reinforced attachment point for stud fittings in cargo restraint assemblies that call for a higher load rating than the standard anchor plate. It...
D-rings are half-round anchor parts used as fixed attachment points for restraint strap and net assemblies. The flat side takes the webbing loop and the round side receives the hook, snap or...
Viewed products
The threaded studs with nut connect equipment, seats and accessory rails to the seat track or to an air cargo pallet attachment, with a standard hex nut that is torqued with a wrench. They are the...
Adjusting plates for 25 and 50 mm webbing, 2 500 daN ultimate load, zinc-plated steel. Length adjustment hardware for restraint and lashing assemblies.
