D-rings for 25 to 50 mm webbing, ultimate loads from 250 to 5 000 daN. Zinc-plated steel or nickel-plated. Half-round attachment points for restraint and tie-down assemblies.
Data sheet
D-rings are half-round anchor parts used as fixed attachment points for restraint strap and net assemblies. The flat side takes the webbing loop and the round side receives the hook, snap or carabiner that connects to the load or structure.
The range covers 25, 45 and 50 mm webbing widths, with ultimate loads from 250 daN for light personal restraint up to 5 000 daN for heavy lashing. Construction is zinc-plated steel for corrosion resistance, or nickel-plated for the lightest 25 mm reference. A flat D-ring variant is available at 5 000 daN for 50 mm webbing, where the flatter cross-section sits closer to the load surface. Unit weights run from 15.6 g to 121 g depending on size.
Stocked as spare parts, compatible with the corresponding GPI Forankra webbing widths.
16 other products in the same category:
Single stud fittings with rings give a one-position anchor point on a seat track or air cargo pallet rail, with an integrated ring that takes the strap or hook directly. They are used for...
The ASNA flat polyester webbing range is manufactured in conformity with Airbus ASNA 3573 standards and is approved for use in aircraft applications under FAR 25 appendix F. It is used for...
The hook with spaced fingers is a heavy-duty end fitting whose two parallel fingers are set apart in a U-shape, engaging spaced bars, grids and double anchor points that a single-finger hook cannot...
S hooks are open end fittings shaped to connect a restraint strap to a bar, anchor ring or rail. The open S-shape allows fast attachment, while latch versions add a safety catch that keeps the hook...
This plastic hook is a lightweight end fitting for 13 mm rope, used in light securing and accessory applications where metal hardware is not required. The plastic construction avoids marking and...
This PVC tarpaulin is the fire-resistant grade specified for use in aircraft cabins and air cargo holds, where any covering material must meet flammability requirements. It is used for load...
Double J hooks are end fittings formed of two J-shaped wire fingers joined to a triangular webbing loop. The two fingers hook onto bars, floor fittings and anchor points, giving a stable engagement...
Snap latches are spring-loaded closures used in cabin restraint and equipment assemblies, where a strap needs to be opened and re-closed often and without tools. A press on the latch releases the...
Adjusting plates are flat steel parts with internal slots that let the webbing fold back on itself and lock by friction, setting the strap length without a buckle. They are used where the assembly...
The threaded studs with nut connect equipment, seats and accessory rails to the seat track or to an air cargo pallet attachment, with a standard hex nut that is torqued with a wrench. They are the...
The lifting ring is a stainless steel delta ring fitted with 4 flat hooks, used as the central gathering point of a lifting net assembly. Each hook is sewn to one corner of the lifting net, and the...
Cam buckles are simple manual tensioning devices for restraint straps. The cam locks the webbing as soon as the lever is released, giving reliable load securing without the bulk or effort of a...
The threaded studs with ergonomic plastic handle connect equipment, seats and accessory rails to the seat track or to an air cargo pallet attachment, with the ergonomic handle allowing tool-free...
Double stud fittings engage two adjacent positions of a seat track or air cargo pallet rail, giving a stronger anchor point than a single stud. They are the standard anchor format for ULD restraint...
This hook combines a fixed eye for permanent attachment with a hooking end fitted with a safety latch. The eye is sewn or pinned to the net edge, and the latched hook engages cabin anchor rings,...
The cargo hook is mounted on the cargo net itself and engages directly in the net mesh to set the working height of the net and adjust its tension over the load. Repositioning the hook from one...
D-rings for 25 to 50 mm webbing, ultimate loads from 250 to 5 000 daN. Zinc-plated steel or nickel-plated. Half-round attachment points for restraint and tie-down assemblies.
