Double J hooks for 25 to 75 mm webbing, ultimate loads from 900 to 10 000 daN. Zinc-plated or stainless steel. Two J-shaped fingers with triangular webbing loop, latch version available.
Data sheet
Double J hooks are end fittings formed of two J-shaped wire fingers joined to a triangular webbing loop. The two fingers hook onto bars, floor fittings and anchor points, giving a stable engagement under load.
The range spans 25 to 75 mm webbing widths, with ultimate loads from 900 daN up to 10 000 daN on the 75 mm version. Construction is zinc-plated steel or stainless steel for corrosion resistance, with unit weights from 29 g to 830 g. A 50 mm version with a security latch is available to lock the hook on the anchor point under vibration.
Stocked as spare parts, compatible with the corresponding GPI Forankra webbing widths.
16 other products in the same category:
Snap latches are spring-loaded closures used in cabin restraint and equipment assemblies, where a strap needs to be opened and re-closed often and without tools. A press on the latch releases the...
The threaded studs with nut connect equipment, seats and accessory rails to the seat track or to an air cargo pallet attachment, with a standard hex nut that is torqued with a wrench. They are the...
This hook-and-loop fastener system is the aerospace counterpart of standard Velcro tape, used in cabin assemblies where a removable fixture is required and where a fire-retardant textile is...
This aircraft seatbelt buckle is used in cabin seat belt and occupant restraint assemblies. It supplies the quick-release connection between the two webbing ends, with male and female parts forming...
The ASNA flat polyester webbing range is manufactured in conformity with Airbus ASNA 3573 standards and is approved for use in aircraft applications under FAR 25 appendix F. It is used for...
The bi-pass buckle is a flat two-slot steel plate for 50 mm webbing. The webbing passes through one slot and back through the second, where it locks by friction. Depending on how it is threaded,...
The seat track range provides aluminium anchoring rails for aircraft seats, cargo restraint systems and cabin equipment. Seat tracks accept stud and stud-fitting hardware along a standardized...
The cargo hook is mounted on the cargo net itself and engages directly in the net mesh to set the working height of the net and adjust its tension over the load. Repositioning the hook from one...
This plastic hook is a lightweight end fitting for 13 mm rope, used in light securing and accessory applications where metal hardware is not required. The plastic construction avoids marking and...
Single stud fittings with rings give a one-position anchor point on a seat track or air cargo pallet rail, with an integrated ring that takes the strap or hook directly. They are used for...
Ratchet buckles are manual tensioning devices for restraint and lashing straps. The ratchet mechanism applies and holds high tension in controlled increments, which makes it the standard choice for...
Over-center buckles are manual tensioning devices that lock the strap with a single lever movement. Compared with a ratchet, the over-center action gives fast, repeatable tension setting without...
Double stud fittings engage two adjacent positions of a seat track or air cargo pallet rail, giving a stronger anchor point than a single stud. They are the standard anchor format for ULD restraint...
The threaded studs with ergonomic plastic handle connect equipment, seats and accessory rails to the seat track or to an air cargo pallet attachment, with the ergonomic handle allowing tool-free...
This hook combines a fixed eye for permanent attachment with a hooking end fitted with a safety latch. The eye is sewn or pinned to the net edge, and the latched hook engages cabin anchor rings,...
These combined fittings pair a slide adjuster with an end hook in a single part, so one component handles both length adjustment and anchoring on a 25 mm strap. They simplify light restraint...
Viewed products
S hooks are open end fittings shaped to connect a restraint strap to a bar, anchor ring or rail. The open S-shape allows fast attachment, while latch versions add a safety catch that keeps the hook...
Flat snap hooks are end fittings for restraint strap assemblies, used to connect the webbing to cabin anchor rings, footman loops and floor fittings. A hinged latch is mounted on a rivet and closes...
Double J hooks for 25 to 75 mm webbing, ultimate loads from 900 to 10 000 daN. Zinc-plated or stainless steel. Two J-shaped fingers with triangular webbing loop, latch version available.
