Double J hooks for 25 to 75 mm webbing, ultimate loads from 900 to 10 000 daN. Zinc-plated or stainless steel. Two J-shaped fingers with triangular webbing loop, latch version available.
Data sheet
Double J hooks are end fittings formed of two J-shaped wire fingers joined to a triangular webbing loop. The two fingers hook onto bars, floor fittings and anchor points, giving a stable engagement under load.
The range spans 25 to 75 mm webbing widths, with ultimate loads from 900 daN up to 10 000 daN on the 75 mm version. Construction is zinc-plated steel or stainless steel for corrosion resistance, with unit weights from 29 g to 830 g. A 50 mm version with a security latch is available to lock the hook on the anchor point under vibration.
Stocked as spare parts, compatible with the corresponding GPI Forankra webbing widths.
16 other products in the same category:
This range of 25 mm flat polyester webbing is used for restraint and lashing assemblies in air transport, where strength, regulatory compliance and color identification matter. It is approved for...
The ASNA flat polyester webbing range is manufactured in conformity with Airbus ASNA 3573 standards and is approved for use in aircraft applications under FAR 25 appendix F. It is used for...
This plastic hook is a lightweight end fitting for 13 mm rope, used in light securing and accessory applications where metal hardware is not required. The plastic construction avoids marking and...
Ratchet buckles are manual tensioning devices for restraint and lashing straps. The ratchet mechanism applies and holds high tension in controlled increments, which makes it the standard choice for...
The 50 mm twisted snap hook is a heavy-duty end fitting for restraint strap assemblies. The hook body is rotated 90° relative to the webbing slot, so the strap lies flat against the airframe or...
D-rings are half-round anchor parts used as fixed attachment points for restraint strap and net assemblies. The flat side takes the webbing loop and the round side receives the hook, snap or...
Rectangular rings are designed to connect two different webbing for an assembly. The range covers four rectangular sizes from 16 to 23 mm with ultimate loads from 100 to 300 daN, and one small...
Quick links are reusable connectors with a screw-gate closure: a threaded sleeve runs along the gate to lock the link closed once a strap or ring is engaged. They replace permanent shackles where a...
The cargo hook is mounted on the cargo net itself and engages directly in the net mesh to set the working height of the net and adjust its tension over the load. Repositioning the hook from one...
The threaded studs with nut connect equipment, seats and accessory rails to the seat track or to an air cargo pallet attachment, with a standard hex nut that is torqued with a wrench. They are the...
This hook-and-loop fastener system is the aerospace counterpart of standard Velcro tape, used in cabin assemblies where a removable fixture is required and where a fire-retardant textile is...
The lifting ring is a stainless steel delta ring fitted with 4 flat hooks, used as the central gathering point of a lifting net assembly. Each hook is sewn to one corner of the lifting net, and the...
The hook with spaced fingers is a heavy-duty end fitting whose two parallel fingers are set apart in a U-shape, engaging spaced bars, grids and double anchor points that a single-finger hook cannot...
S hooks are open end fittings shaped to connect a restraint strap to a bar, anchor ring or rail. The open S-shape allows fast attachment, while latch versions add a safety catch that keeps the hook...
Flat hooks are end fittings for restraint strap assemblies, connecting the webbing to cabin anchor rings, footman loops and floor fittings. The open-throat shape gives fast hook-on and hook-off in...
Single stud fittings with rings give a one-position anchor point on a seat track or air cargo pallet rail, with an integrated ring that takes the strap or hook directly. They are used for...
Viewed products
The seat track range provides aluminium anchoring rails for aircraft seats, cargo restraint systems and cabin equipment. Seat tracks accept stud and stud-fitting hardware along a standardized...
Double J hooks for 25 to 75 mm webbing, ultimate loads from 900 to 10 000 daN. Zinc-plated or stainless steel. Two J-shaped fingers with triangular webbing loop, latch version available.
