Round rings from 23 to 70 mm, ultimate loads from 500 to 4 000 daN. Closed anchor points for restraint, tie-down and lifting assemblies.
Data sheet
Round rings are closed anchor parts used as connection points in restraint, tie-down and lifting assemblies. The closed shape lets straps, slings and connectors run all the way around the ring, which spreads the load and gives an even distribution at the contact point.
The range covers six ring sizes from 23 to 70 mm in inner diameter, with ultimate loads stepping up from 500 daN on the smallest sizes to 4 000 daN on the 50 and 70 mm references. Two load ratings are available on both the 50 mm and 70 mm sizes, so the right strength can be selected for the application without changing ring geometry.
Stocked as spare parts for assemblies that need a closed anchor point rather than an open D-ring or hook.
16 other products in the same category:
This range of 25 mm flat polyester webbing is used for restraint and lashing assemblies in air transport, where strength, regulatory compliance and color identification matter. It is approved for...
Raschel netting is a knitted mesh fabric supplied by the metre and used to build cabin partitions, baggage retention curtains and custom net assemblies that need a textile mesh rather than a...
The bi-pass buckle is a flat two-slot steel plate for 50 mm webbing. The webbing passes through one slot and back through the second, where it locks by friction. Depending on how it is threaded,...
The cargo hook is mounted on the cargo net itself and engages directly in the net mesh to set the working height of the net and adjust its tension over the load. Repositioning the hook from one...
This PVC tarpaulin is the fire-resistant grade specified for use in aircraft cabins and air cargo holds, where any covering material must meet flammability requirements. It is used for load...
This aircraft seatbelt buckle is used in cabin seat belt and occupant restraint assemblies. It supplies the quick-release connection between the two webbing ends, with male and female parts forming...
The threaded studs with nut connect equipment, seats and accessory rails to the seat track or to an air cargo pallet attachment, with a standard hex nut that is torqued with a wrench. They are the...
Fixation plates are flat anchor parts used to bolt the end of a webbing strap to the airframe, a load platform or any structure with matching threaded holes. The webbing loops through the plate,...
This hook-and-loop fastener system is the aerospace counterpart of standard Velcro tape, used in cabin assemblies where a removable fixture is required and where a fire-retardant textile is...
The lifting ring is a stainless steel delta ring fitted with 4 flat hooks, used as the central gathering point of a lifting net assembly. Each hook is sewn to one corner of the lifting net, and the...
Rectangular rings are designed to connect two different webbing for an assembly. The range covers four rectangular sizes from 16 to 23 mm with ultimate loads from 100 to 300 daN, and one small...
This hook combines a fixed eye for permanent attachment with a hooking end fitted with a safety latch. The eye is sewn or pinned to the net edge, and the latched hook engages cabin anchor rings,...
The 50 mm twisted snap hook is a heavy-duty end fitting for restraint strap assemblies. The hook body is rotated 90° relative to the webbing slot, so the strap lies flat against the airframe or...
Over-center buckles are manual tensioning devices that lock the strap with a single lever movement. Compared with a ratchet, the over-center action gives fast, repeatable tension setting without...
D-rings are half-round anchor parts used as fixed attachment points for restraint strap and net assemblies. The flat side takes the webbing loop and the round side receives the hook, snap or...
The threaded studs with ergonomic plastic handle connect equipment, seats and accessory rails to the seat track or to an air cargo pallet attachment, with the ergonomic handle allowing tool-free...
Viewed products
Rectangular rings are designed to connect two different webbing for an assembly. The range covers four rectangular sizes from 16 to 23 mm with ultimate loads from 100 to 300 daN, and one small...
Round rings from 23 to 70 mm, ultimate loads from 500 to 4 000 daN. Closed anchor points for restraint, tie-down and lifting assemblies.
