D-rings for 25 to 50 mm webbing, ultimate loads from 250 to 5 000 daN. Zinc-plated steel or nickel-plated. Half-round attachment points for restraint and tie-down assemblies.
Data sheet
D-rings are half-round anchor parts used as fixed attachment points for restraint strap and net assemblies. The flat side takes the webbing loop and the round side receives the hook, snap or carabiner that connects to the load or structure.
The range covers 25, 45 and 50 mm webbing widths, with ultimate loads from 250 daN for light personal restraint up to 5 000 daN for heavy lashing. Construction is zinc-plated steel for corrosion resistance, or nickel-plated for the lightest 25 mm reference. A flat D-ring variant is available at 5 000 daN for 50 mm webbing, where the flatter cross-section sits closer to the load surface. Unit weights run from 15.6 g to 121 g depending on size.
Stocked as spare parts, compatible with the corresponding GPI Forankra webbing widths.
16 other products in the same category:
The ASNA flat polyester webbing range is manufactured in conformity with Airbus ASNA 3573 standards and is approved for use in aircraft applications under FAR 25 appendix F. It is used for...
This aircraft seatbelt buckle is used in cabin seat belt and occupant restraint assemblies. It supplies the quick-release connection between the two webbing ends, with male and female parts forming...
The threaded studs with nut connect equipment, seats and accessory rails to the seat track or to an air cargo pallet attachment, with a standard hex nut that is torqued with a wrench. They are the...
This tubular polyester webbing is used for corner ropes and lashing assemblies in air transport. The tubular construction spreads the load around the full circumference of the strap, which limits...
Raschel netting is a knitted mesh fabric supplied by the metre and used to build cabin partitions, baggage retention curtains and custom net assemblies that need a textile mesh rather than a...
These combined fittings pair a slide adjuster with an end hook in a single part, so one component handles both length adjustment and anchoring on a 25 mm strap. They simplify light restraint...
This single stud fitting integrates a length adjuster on the stud body, so one component handles both the seat track or pallet anchor and the adjustment of the connected strap. It simplifies...
Adjusting plates are flat steel parts with internal slots that let the webbing fold back on itself and lock by friction, setting the strap length without a buckle. They are used where the assembly...
This hook-and-loop fastener system is the aerospace counterpart of standard Velcro tape, used in cabin assemblies where a removable fixture is required and where a fire-retardant textile is...
Ratchet buckles are manual tensioning devices for restraint and lashing straps. The ratchet mechanism applies and holds high tension in controlled increments, which makes it the standard choice for...
This aluminium double anchor plate provides a reinforced attachment point for stud fittings in cargo restraint assemblies that call for a higher load rating than the standard anchor plate. It...
Cam buckles are simple manual tensioning devices for restraint straps. The cam locks the webbing as soon as the lever is released, giving reliable load securing without the bulk or effort of a...
Flat hooks are end fittings for restraint strap assemblies, connecting the webbing to cabin anchor rings, footman loops and floor fittings. The open-throat shape gives fast hook-on and hook-off in...
The hook with spaced fingers is a heavy-duty end fitting whose two parallel fingers are set apart in a U-shape, engaging spaced bars, grids and double anchor points that a single-finger hook cannot...
The seat track covering is a flexible strip that fits into unused seat track sections to keep debris, fluids and foreign objects out of the rail pitch. It protects the track and reduces foreign...
The threaded studs with ergonomic plastic handle connect equipment, seats and accessory rails to the seat track or to an air cargo pallet attachment, with the ergonomic handle allowing tool-free...
D-rings for 25 to 50 mm webbing, ultimate loads from 250 to 5 000 daN. Zinc-plated steel or nickel-plated. Half-round attachment points for restraint and tie-down assemblies.
