Round rings from 23 to 70 mm, ultimate loads from 500 to 4 000 daN. Closed anchor points for restraint, tie-down and lifting assemblies.
Data sheet
Round rings are closed anchor parts used as connection points in restraint, tie-down and lifting assemblies. The closed shape lets straps, slings and connectors run all the way around the ring, which spreads the load and gives an even distribution at the contact point.
The range covers six ring sizes from 23 to 70 mm in inner diameter, with ultimate loads stepping up from 500 daN on the smallest sizes to 4 000 daN on the 50 and 70 mm references. Two load ratings are available on both the 50 mm and 70 mm sizes, so the right strength can be selected for the application without changing ring geometry.
Stocked as spare parts for assemblies that need a closed anchor point rather than an open D-ring or hook.
16 other products in the same category:
Flat hooks are end fittings for restraint strap assemblies, connecting the webbing to cabin anchor rings, footman loops and floor fittings. The open-throat shape gives fast hook-on and hook-off in...
This aluminium double anchor plate provides a reinforced attachment point for stud fittings in cargo restraint assemblies that call for a higher load rating than the standard anchor plate. It...
This aircraft seatbelt buckle is used in cabin seat belt and occupant restraint assemblies. It supplies the quick-release connection between the two webbing ends, with male and female parts forming...
Slide buckles are length-adjustment fittings for webbing straps. The webbing threads through the buckle and locks by friction, allowing manual adjustment of the strap length without a tensioning...
Snap latches are spring-loaded closures used in cabin restraint and equipment assemblies, where a strap needs to be opened and re-closed often and without tools. A press on the latch releases the...
This tubular polyester webbing is used for corner ropes and lashing assemblies in air transport. The tubular construction spreads the load around the full circumference of the strap, which limits...
The lifting ring is a stainless steel delta ring fitted with 4 flat hooks, used as the central gathering point of a lifting net assembly. Each hook is sewn to one corner of the lifting net, and the...
This hook combines a fixed eye for permanent attachment with a hooking end fitted with a safety latch. The eye is sewn or pinned to the net edge, and the latched hook engages cabin anchor rings,...
Quick links are reusable connectors with a screw-gate closure: a threaded sleeve runs along the gate to lock the link closed once a strap or ring is engaged. They replace permanent shackles where a...
Over-center buckles are manual tensioning devices that lock the strap with a single lever movement. Compared with a ratchet, the over-center action gives fast, repeatable tension setting without...
Rectangular rings are designed to connect two different webbing for an assembly. The range covers four rectangular sizes from 16 to 23 mm with ultimate loads from 100 to 300 daN, and one small...
These combined fittings pair a slide adjuster with an end hook in a single part, so one component handles both length adjustment and anchoring on a 25 mm strap. They simplify light restraint...
This aluminium anchor plate provides a fixed attachment point for single stud fittings in cargo restraint assemblies. It is used to anchor straps and nets to the aircraft structure or to load...
D-rings are half-round anchor parts used as fixed attachment points for restraint strap and net assemblies. The flat side takes the webbing loop and the round side receives the hook, snap or...
The threaded studs with nut connect equipment, seats and accessory rails to the seat track or to an air cargo pallet attachment, with a standard hex nut that is torqued with a wrench. They are the...
The ASNA flat polyester webbing range is manufactured in conformity with Airbus ASNA 3573 standards and is approved for use in aircraft applications under FAR 25 appendix F. It is used for...
Viewed products
Footman loops are U-shaped bolt-down anchor points fixed to the cabin floor, cargo platform or equipment panel, giving a hook-on point for a restraint or lashing strap. They are the most common...
Rectangular rings are designed to connect two different webbing for an assembly. The range covers four rectangular sizes from 16 to 23 mm with ultimate loads from 100 to 300 daN, and one small...
Round rings from 23 to 70 mm, ultimate loads from 500 to 4 000 daN. Closed anchor points for restraint, tie-down and lifting assemblies.
