Footman loops for 25 mm webbing, 900 daN ultimate load, zinc-plated or nickel-plated steel. Bolt-down floor and panel anchor points for restraint strap assemblies.
Data sheet
Footman loops are U-shaped bolt-down anchor points fixed to the cabin floor, cargo platform or equipment panel, giving a hook-on point for a restraint or lashing strap. They are the most common anchor format for 25 mm strap assemblies in aircraft cabins, military vehicles and stowage racks.
Both references take 25 mm webbing and have a 900 daN ultimate load. A nickel-plated steel version (53 mm long, 17 g) gives a cleaner cabin finish, and a zinc-plated steel version (48 mm long, 16 g) suits standard cargo and equipment installations. Thickness is 12 mm for both.
Stocked as spare parts for restraint assemblies and aircraft cabin installations.
16 other products in the same category:
The threaded studs with ergonomic plastic handle connect equipment, seats and accessory rails to the seat track or to an air cargo pallet attachment, with the ergonomic handle allowing tool-free...
This range of 25 mm flat polyester webbing is used for restraint and lashing assemblies in air transport, where strength, regulatory compliance and color identification matter. It is approved for...
This plastic hook is a lightweight end fitting for 13 mm rope, used in light securing and accessory applications where metal hardware is not required. The plastic construction avoids marking and...
Flat snap hooks are end fittings for restraint strap assemblies, used to connect the webbing to cabin anchor rings, footman loops and floor fittings. A hinged latch is mounted on a rivet and closes...
Quick links are reusable connectors with a screw-gate closure: a threaded sleeve runs along the gate to lock the link closed once a strap or ring is engaged. They replace permanent shackles where a...
These combined fittings pair a slide adjuster with an end hook in a single part, so one component handles both length adjustment and anchoring on a 25 mm strap. They simplify light restraint...
Double stud fittings engage two adjacent positions of a seat track or air cargo pallet rail, giving a stronger anchor point than a single stud. They are the standard anchor format for ULD restraint...
Over-center buckles are manual tensioning devices that lock the strap with a single lever movement. Compared with a ratchet, the over-center action gives fast, repeatable tension setting without...
Rectangular rings are designed to connect two different webbing for an assembly. The range covers four rectangular sizes from 16 to 23 mm with ultimate loads from 100 to 300 daN, and one small...
S hooks are open end fittings shaped to connect a restraint strap to a bar, anchor ring or rail. The open S-shape allows fast attachment, while latch versions add a safety catch that keeps the hook...
The threaded studs with nut connect equipment, seats and accessory rails to the seat track or to an air cargo pallet attachment, with a standard hex nut that is torqued with a wrench. They are the...
The ASNA flat polyester webbing range is manufactured in conformity with Airbus ASNA 3573 standards and is approved for use in aircraft applications under FAR 25 appendix F. It is used for...
D-rings are half-round anchor parts used as fixed attachment points for restraint strap and net assemblies. The flat side takes the webbing loop and the round side receives the hook, snap or...
Raschel netting is a knitted mesh fabric supplied by the metre and used to build cabin partitions, baggage retention curtains and custom net assemblies that need a textile mesh rather than a...
The hook with spaced fingers is a heavy-duty end fitting whose two parallel fingers are set apart in a U-shape, engaging spaced bars, grids and double anchor points that a single-finger hook cannot...
Round rings are closed anchor parts used as connection points in restraint, tie-down and lifting assemblies. The closed shape lets straps, slings and connectors run all the way around the ring,...
Footman loops for 25 mm webbing, 900 daN ultimate load, zinc-plated or nickel-plated steel. Bolt-down floor and panel anchor points for restraint strap assemblies.
