25 mm hook and loop tape conforming to Airbus ASNA 3546 standards and FAR 25.853. Available in white, black and grey. For aircraft cabin assemblies and removable fixtures.
Data sheet
This hook-and-loop fastener system is the aerospace counterpart of standard Velcro tape, used in cabin assemblies where a removable fixture is required and where a fire-retardant textile is mandatory. Hook tape (ASNA 3546-1875) and loop tape (ASNA 3546-1825) are sold separately so the right combination can be assembled for the application.
Width is 25 mm for both tapes, with a uniform weight of 15 g/m. Standard colors are white, black and grey, to match cabin finishes and equipment liveries. The fastener is approved for use in aircraft under FAR 25 appendix F and conforms to the Airbus ASNA 3546 specifications.
Other widths are available on demand for specific cabin installations.
16 other products in the same category:
Belt buckles supply a quick connection for light belt and restraint assemblies, with male and female parts forming the complete buckle. They are used for equipment belts, light cabin restraints and...
Snap latches are spring-loaded closures used in cabin restraint and equipment assemblies, where a strap needs to be opened and re-closed often and without tools. A press on the latch releases the...
This PVC tarpaulin is the fire-resistant grade specified for use in aircraft cabins and air cargo holds, where any covering material must meet flammability requirements. It is used for load...
The cargo hook is mounted on the cargo net itself and engages directly in the net mesh to set the working height of the net and adjust its tension over the load. Repositioning the hook from one...
Flat hooks are end fittings for restraint strap assemblies, connecting the webbing to cabin anchor rings, footman loops and floor fittings. The open-throat shape gives fast hook-on and hook-off in...
The bi-pass buckle is a flat two-slot steel plate for 50 mm webbing. The webbing passes through one slot and back through the second, where it locks by friction. Depending on how it is threaded,...
This end fitting carries a latched hook mounted on a triangular delta ring, the delta ring taking the 50 mm webbing and the latched hook engaging on anchor rings, floor fittings and other...
This range of 25 mm flat polyester webbing is used for restraint and lashing assemblies in air transport, where strength, regulatory compliance and color identification matter. It is approved for...
Over-center buckles are manual tensioning devices that lock the strap with a single lever movement. Compared with a ratchet, the over-center action gives fast, repeatable tension setting without...
This aircraft seatbelt buckle is used in cabin seat belt and occupant restraint assemblies. It supplies the quick-release connection between the two webbing ends, with male and female parts forming...
Ratchet buckles are manual tensioning devices for restraint and lashing straps. The ratchet mechanism applies and holds high tension in controlled increments, which makes it the standard choice for...
Flat snap hooks are end fittings for restraint strap assemblies, used to connect the webbing to cabin anchor rings, footman loops and floor fittings. A hinged latch is mounted on a rivet and closes...
The hook with spaced fingers is a heavy-duty end fitting whose two parallel fingers are set apart in a U-shape, engaging spaced bars, grids and double anchor points that a single-finger hook cannot...
D-rings are half-round anchor parts used as fixed attachment points for restraint strap and net assemblies. The flat side takes the webbing loop and the round side receives the hook, snap or...
This aluminium double anchor plate provides a reinforced attachment point for stud fittings in cargo restraint assemblies that call for a higher load rating than the standard anchor plate. It...
The seat track covering is a flexible strip that fits into unused seat track sections to keep debris, fluids and foreign objects out of the rail pitch. It protects the track and reduces foreign...
Viewed products
The hook with spaced fingers is a heavy-duty end fitting whose two parallel fingers are set apart in a U-shape, engaging spaced bars, grids and double anchor points that a single-finger hook cannot...
25 mm hook and loop tape conforming to Airbus ASNA 3546 standards and FAR 25.853. Available in white, black and grey. For aircraft cabin assemblies and removable fixtures.
